Crestron Control Information Gating Controls See below for a sample screen. SIMPLWINDOWS NAME: ASPI Vortex Gating MANUFACTURER: Polycom MODEL: Vortex (EF2280) CATEGORY: MIXER VERSION: 1.0 SUMMARY: Allows monitoring of gating status GENERAL NOTES: The commands used for the Vortex may be similar to commands used for other EF products. Therefore, the same modules developed for the Vortex may work on other EF products. To allow for this flexibility of use, you must specify which model is being controlled using the TYPE-ID-HEX parameter field. This must be a 2 digit hex representation of the model type as defined by Polycom. For the Vortex, the model type is F, therefore the parameter value to use is 46 which is the hex representation of the letter F. This can be seen by checking any standard ASCII chart. There should be no suffix used after the 46. Multiple devices can be connected to the ASPI bus and controlled from a single RS232 port. Therefore, it is also necessary to enter the Unit ID of the device being controlled. This should be entered in the UNIT-ID-ASCII parameter field as a two digit number from 00-07 with no suffix. This module allows the automatic reporting of gating status to be enabled/disabled. If the automatic gating status is disabled, you can use the POLL input to manually poll the gating status. This module will reflect the gating status at the MIC-*-ON outputs. CRESTRON HARDWARE REQUIRED: CNXCOM, ST-COM SETUP OF CRESTRON HARDWARE: Baud Rate - 9600 Parity - None Data Bits - 8 Stop Bits - 1 RTS/CTS Handshaking should be enabled to insure no data is lost. VENDOR FIRMWARE: 1.15 VENDOR SETUP: Ack mode must be set to "on" CABLE NUMBER: CNSP-141 INPUT DESCRIPTIONS: Name Type Description ENABLE/DISABLE-AUTO-UPDATE D Pulse to enable or disable the automatic reporting of the gating status POLL D Pulse to manually poll the gating status. This should not be needed if automatic reporting has been enabled FROM-ASPI-PROCESSOR$ S Must be routed from the output of the Vortex Feedback Processor module TYPE-ID-ASCII P Enter 46 for Vortex UNIT-ID-ASCII P Enter the unit number of the Vortex. Should be a number from 00-07 OUTPUT DESCRIPTIONS: Name Type Description MIC-*-ON D True feedback indicating which mics are gated on ASPI-TX$ S Serial signal to be routed to a 2-way RS232 port OPS USED FOR TESTING: 5.12.26x COMPILER USED FOR TESTING: SimplWindows Ver 1.61.12 SAMPLE PROGRAM: Vortex Demo Program REVISION HISTORY: None Camera Gating Controls SIMPLWINDOWS NAME: Vortex Camera Gating MANUFACTURER: ASPI MODEL: Vortex (EF2280) CATEGORY: MIXER VERSION: 1.0 SUMMARY: Allows monitoring of camera gating status GENERAL NOTES: The commands used for the Polycom Vortex may be similar to commands used for other EF products. Therefore, the same modules developed for the Vortex may work on other EF products. To allow for this flexibility of use, you must specify which model is being controlled using the TYPE-ID-HEX parameter field. This must be a 2 digit hex representation of the model type as defined by Polycom. For the Vortex, the model type is F, therefore the parameter value to use is 46 which is the hex representation of the letter F. This can be seen by checking any standard ASCII chart. There should be no suffix used after the 46. Multiple devices can be connected to the ASPI bus and controlled from a single RS232 port. Therefore, it is also necessary to enter the Unit ID of the device being controlled. This should be entered in the UNIT-ID-ASCII parameter field as a two digit number from 00-07 with no suffix. This module allows the automatic reporting of camera gating status to be enabled/disabled. If the automatic gating status is disabled, you can use the POLL input to manually poll the gating status. This module will reflect the gating status at the MIC-*-ON outputs. CRESTRON HARDWARE REQUIRED: CNXCOM, ST-COM SETUP OF CRESTRON HARDWARE: Baud Rate - 9600 Parity - None Data Bits - 8 Stop Bits - 1 RTS/CTS Handshaking should be enabled to insure no data is lost. VENDOR FIRMWARE: 1.15 VENDOR SETUP: Ack mode must be set to "on" CABLE NUMBER: CNSP-141 INPUT DESCRIPTIONS: Name Type / Description ENABLE/DISABLE-AUTO-UPDATE D Pulse to enable or disable the automatic reporting of the gating status POLL D Pulse to manually poll the gating status. This should not be needed if automatic reporting has been enabled FROM-ASPI-PROCESSOR$ S Must be routed from the output of the Vortex Feedback Processor module TYPE-ID-ASCII P Enter 46 for Vortex UNIT-ID-ASCII P Enter the unit number of the Vortex. Should be a number from 00-07 OUTPUT DESCRIPTIONS: Name Type / Description MIC-*-ON D True feedback indicating which mics are gated on ASPI-TX$ S Serial signal to be routed to a 2-way RS232 port OPS USED FOR TESTING: 5.12.26x COMPILER USED FOR TESTING: SimplWindows Ver 1.61.12 SAMPLE PROGRAM: Vortex Demo Program REVISION HISTORY: None Logic Inputs and Outputs Macro and Preset Controls Line Level Input Controls Mic Input Controls Output Controls Crestron Website Back to Main Page | Contact Us Products Technical Resources | More About Us Polycom Installed Voice Business Group 1720 Peachtree St NW, Suite 220 Atlanta,GA 30309 telephone: 404.892.3200 fax: 404.892.2512 e-mail us